- HOW TO SET UP RETROPIE 3.5 HOW TO
- HOW TO SET UP RETROPIE 3.5 INSTALL
- HOW TO SET UP RETROPIE 3.5 DRIVER
- HOW TO SET UP RETROPIE 3.5 DOWNLOAD
HOW TO SET UP RETROPIE 3.5 DRIVER
Changing these will not have any effect on the fbtft driver presented on /dev/fb1. Mixing information for the JBtek documents and mine is a recipe for failure.Ī) The framebuffer_* values in the config file are specifically for the Raspberry Pi’s own display controller presented on /dev/fb0. They are not the same or compatible with each other. No promises though.ĭon’t confuse the so called “driver” provided by JBtek and the one that I have documented.
HOW TO SET UP RETROPIE 3.5 HOW TO
If I get some time I might do an updated page showing how to use the dti files for the MZ61581. FAT32 does not support Linux file permissions (read/write/execute and user/group etc) so when tar tries to set these attributes on the file the file system generates an error. These are because the /boot partition on the SD card is FAT32. So the newer Raspberry pi images have probably moved past where things were at when I wrote the howto. Bare in mind that my howto is more than 6 months old now and things in Linux move quite fast. You will probably need to undo changes you have made to the files listed in my howto. Here is the dti file you will need for the MZ61581. See here for instructions on building dti files: However you will need to get a device tree overlay file first. The MZ61581 should be supported by the default kernel from raspberry pi. input: ADS7846 Touchscreen as /devices/platform/bcm2708_spi.0/spi_master/spi0/spi0.1/input/input0 graphics fb1: fb_ili9486 frame buffer, 480×320, 300 KiB video memory, 4 KiB DMA buffer memory, fps=20, spi0.0 at 128 MHz
fbtft_device: GPIOS used by ‘tontec35_9486’: fbtft_device: bcm2708_fb id=-1 pdata? no fbtft_device: ‘fb’ Platform devices registered: fbtft_device: spidev spi0.1 500kHz 8 bits mode=0x00 fbtft_device: spidev spi0.0 500kHz 8 bits mode=0x00 Then I compiled the “MZ元50I-PI-EXT LCD Display Module” (mzl350i-pi-ext.rar) and executed the “lcd” test file which finally turned on my screen and displayed the terminal screen, but I could not get this to reproduce on boot… I downloaded the custom distro (mz9486-20150107.rar) which I was told supports this NEWEST device (distro dated 1/7/2o15), but I could not get it to work during boot.
HOW TO SET UP RETROPIE 3.5 DOWNLOAD
(C) Can you start with a normal distro of Raspian or do you need to download a modified kernel from the manufacturer’s support site? (B) Can you use the old base driver and pass it the new “init data” ?Īccordingly, here is the hexadecimal init data for this new driver:
HOW TO SET UP RETROPIE 3.5 INSTALL
(A) How to install support for this new model? TROUBLE: During boot process the screen will init with a black screen then transitions to a white-out. The third model, the “2015 Edition”, currently has no FBTFT device driver support. If you ordered during December of 2014, you most likely recieved their latest production model dated “12-28-14”. SUMMARY: The Tontec 3.5″ 2015 Edition Touch Screen released. WANTED: How to install the third edition of Tontec TFT device for Pi. Waiting for X server to shut down Server terminated successfully (0). > Warning: Type “ONE_LEVEL” has 1 levels, but has 2 symbolsĮrrors from xkbcomp are not fatal to the X server The XKEYBOARD keymap compiler (xkbcomp) reports:
(=) Using system config directory “/usr/share/X11/” (WW) warning, (EE) error, (NI) not implemented, (?) unknown. (++) from command line, (!!) notice, (II) informational, Markers: (–) probed, (**) from config file, (=) default setting, To make sure that you have the latest version. Xorg-server 2:1.12.4-6+deb7u5 (Moritz Muehlenhoff ) Below is the response I would really appreciate it if you could take a look at ~ $ startxīuild Operating System: Linux 3.2.0-2-mx5 armv7l DebianĬurrent Operating System: Linux raspberrypi 3.12.34+ #1 PREEMPT Sun Dec 7 22:39: armv6l The LCD still not coming on so I used Putty to continue with your steps and i got stock at startX line.